Compliance Documents and Requirements
Two certificates in this range carry a number that can be checked. Everything else is supplied per market, per order. This page separates the two, because a buyer who cannot tell them apart ends up relying on the wrong document.
UNECE R10 (EMC) · CE technical file · Vehicle-side standards · Who signs what
We supply. We do not sign.
Velomove is a supplier and export partner, not the legal manufacturer. The approvals below are held by Changzhou Xinder-Tech Electronics Co., Ltd., established 2001, whose authorized sales and export partner Velomove is. That distinction decides who can sign a declaration and who cannot.
It also means the honest answer to “can you send a DoC?” is: we can request it, we cannot issue it. A declaration signed by a company that did not build the unit is worth nothing at a border or an inspection.
- Manufacturer and certificate holder — Changzhou Xinder-Tech Electronics Co., Ltd. Holds the approvals, issues declarations, keeps the technical file.
- Supplier and export partner — Velomove. Specifies, supplies, provides fitment data, requests documents on your behalf, answers the test house.
- Installer or converter — the local workshop. Owns the physical installation, the vehicle preparation and the post-conversion inspection in the market where the vehicle is registered.
Where a document does not exist for a model, we say it does not exist. Substituting a similar file from another product family is how buyers get stopped at customs.
The two documents with a traceable number
Both are held by the manufacturer. Both have a scope narrower than the phrase “CE certified” suggests, and both are worth reading to the last line before you put them in a tender response.
UNECE R10 — EMC of the SLIFT swivel seat range
E49*10R06/03*20011*00
- Type approval no.
- E49*10R06/03*20011*00
- Approval authority
- E49 — Cyprus
- Date of approval
- 28 June 2025
- Test report
- CN-24-B1-25147-P00649
- Product scope
- Four SLIFT swivel seat models
- Holder
- Changzhou Xinder-Tech Electronics Co., Ltd.
Scope: electromagnetic compatibility only. R10 does not test mechanical strength, static load, cycle life or the locking mechanism. It is not a product safety certificate and should not be presented as one.
CE technical file — WL-D wheelchair lift series
11/32300058
- File number
- 11/32300058
- Issued by
- LGAI Technological Center, S.A. (Applus)
- Notified body
- 0370
- Date
- 2 February 2011
- Product scope
- WL-D wheelchair lift series only
- Holder
- Changzhou Xinder-Tech Electronics Co., Ltd.
Drawn up in 2011 against the directive then in force. Whether it still satisfies the current directive for a specific market has to be confirmed before it is relied on, and it does not extend to the swivel seats or the ramps.
Copies of both are sent with a quotation on request. If your enquiry is for a model outside these two scopes, ask what exists before you assume something does.
What applies where, and who does the rest
A product that is in order in one market is not automatically in order in the next. The table below is a starting point for the conversation, not legal advice — the regulation text in the destination market governs.
| Market | What usually applies | What we supply | What the buyer or installer does |
|---|---|---|---|
| European Union | EMC Directive 2014/30/EU; Machinery Directive 2006/42/EC (its replacement applies from 2027); UNECE R10 for vehicle-fitted electrical equipment | R10 approval copy, WL-D technical file, manufacturer’s declaration on request | Vehicle registration or modification approval after fitting; national inspection |
| United Kingdom | UKCA marking; UNECE regulations recognized in GB type approval | Same documents as the EU, plus the manufacturer’s UK-side statement where held | DVSA or equivalent inspection for a converted vehicle |
| United States | FMVSS 403 and 404 govern platform lifts on motor vehicles — these are vehicle standards; ADA applies to public transport service, not to a private conversion | Product drawings, test reports from the manufacturing partner, component lists | Converter or upfitter holds the FMVSS position; we do not claim ADA compliance for these products |
| Canada | CMVSS equivalents of the US standards, administered per province | Same technical pack as the US | Provincial inspection after conversion |
| Australia and New Zealand | Australian Design Rules for the vehicle; state-based modification approval | Technical pack and compliance documents on request | State signatory or approved workshop for the modification |
| Gulf and Middle East | GCC standardisation and national vehicle inspection regimes | Documents on request, market dependent | Local importer registration and inspection |
| Rest of world | National vehicle and electrical rules, often derived from UNECE | Compliance documents on request (market dependent) | Local registration and inspection |
A lift with an EMC approval can still fail a vehicle inspection if the anchorage was not signed off. The two are separate steps and separate documents.
Cutting a floor or replacing a seat base makes the workshop the modifying party in almost every jurisdiction. That is where the inspection obligation lands.
If a tender requires a certificate number, send us the clause first. It is faster to find out which number exists than to withdraw a bid later.
ISO 10542 and UNECE R107 do different jobs
The two are routinely quoted as if they were interchangeable. They are not. ISO 10542 is a product standard for the tie-down and occupant restraint system: straps, buckles, anchorages and the loads they must survive. UNECE R107 is a vehicle standard for M2 and M3 buses, covering the wheelchair space, the door and aisle clearances and the anchorage points built into the vehicle.
Velomove supplies the restraint system, not the bus. So the first is ours to document and the second belongs to whoever builds or converts the vehicle.
Wheelchair tie-down and restraint system
Four-point strap tie-down with a three-point occupant restraint, documented against ISO 10542 and intended for van and minibus installations where the passenger stays in the wheelchair.
See the restraint systemWhat we do not claim
Written down because the omission is easier to check than the claim. If a competitor’s datasheet shows a mark this list does not, ask them for the certificate number before you believe it.
- No CCC, no GB standard reference and no ISO 9001. None of the three is held for these ranges, so none appears on a datasheet. Quality control at the manufacturing partner is described in the audit pack, not implied by a logo.
- No CE mark on the swivel seats or the ramps. The only CE deliverable we hold is the WL-D technical file listed above.
- No ADA compliance claim. ADA governs public transport service in the United States; it is not a product certificate. FMVSS 403 and 404 are vehicle-level standards held by the converter.
- No country counts, no unit counts, no “global first”. Figures like “exported to 60 countries” cannot be verified by a buyer, so we do not print them.
Frequently Asked Questions
Seven questions buyers ask before they place a first order, answered with the document numbers we can actually quote.
What does the UNECE R10 approval actually cover?
Electromagnetic compatibility only. The approval number is E49*10R06/03*20011*00, issued on 28 June 2025 under the E49 authority, with test report CN-24-B1-25147-P00649. It covers the four SLIFT swivel seat models as electrical equipment fitted to a vehicle. It says nothing about mechanical strength, static load or cycle life.
Is the CE technical file valid for every product you supply?
No. Technical file 11/32300058 was drawn up on 2 February 2011 by LGAI Technological Center (Applus, notified body 0370) and covers the WL-D wheelchair lift series only. It was written against the directive in force in 2011, so whether it still satisfies the current directive for a given market has to be checked before it is relied on. It is not presented as cover for the swivel seats, the ramps or the other lift families.
Can you issue a Declaration of Conformity?
No. The declaration is issued by the manufacturer, Changzhou Xinder-Tech Electronics Co., Ltd., and Velomove is its authorized sales and export partner, not the legal manufacturer. We request the declaration per order and per destination market and send the original with the shipment documents. A declaration signed by Velomove would not be valid.
Do your products carry CCC or ISO 9001?
We hold no CCC certificate and no ISO 9001 certificate for these product ranges, and we do not claim either in a quotation or on a datasheet. What we can put in writing is narrower and verifiable: the R10 EMC approval above, the WL-D technical file above, and test reports from the manufacturing partner for the specific model being quoted.
Which standard applies to wheelchair tie-downs and occupant restraints?
Two, and they do different jobs. ISO 10542 covers the tie-down and occupant restraint system as a product: the straps, the anchorages and the test loads. UNECE R107 covers the vehicle side, meaning the wheelchair space, the door and aisle clearances and the anchorage points in an M2 or M3 bus. The Velomove restraint system is documented against the first; the second is a property of the vehicle the installer is working on.
After installation, who certifies the converted vehicle?
The installer or converter, in the country where the vehicle is registered. Fitting a swivel seat or a lift changes the seat anchorage or the body structure, and most markets treat that as a modification requiring inspection, re-registration or an engineering sign-off. Velomove supplies the product documents and the fitment data; we do not issue vehicle approvals and cannot act as the inspecting body.
What language are the documents in, and can they be reissued?
English by default. Manuals and labels can be reissued in another language for a volume order, and the certificate copies are the original documents, not retyped versions. If a buyer needs a document we do not hold, we say so rather than substituting a similar-looking file.
Three useful doors
Compliance is usually the second question. Fitment is the first, and buying terms the third.
Buying guide
The four measurements that decide between a swivel seat, a lift and a ramp, and the mistakes that stop a fit.
Read the guideOEM and private label
Branded units, agreed specifications and where the manufacturing actually happens.
See the programInstallation partners
Who fits the unit, what support comes with it, and where our responsibility ends.
See the network