Wheelchair Lift and Swivel Seat Buying Guide
Four measurements decide which product you need. Everything else — brand, price, lead time — is secondary to whether the unit physically completes its movement at your door.
Measure first · Choose the type · Match the model · Install and inspect
Four numbers, taken with the vehicle in front of you
These are not rough figures to be estimated from a brochure. Every one of them is measured on the actual vehicle, because trim, seat rails and optional equipment move them by tens of millimeters.
Door clear width
Widest point of the opening with the door fully open, not the door frame. A swivel seat needs the passenger to pass through it while seated, so this is usually the figure that fails first.
Door clear height
Floor to the lowest point of the aperture. On the SLIFT Plus and SLIFT Plus+ the published minimum is 990 mm; below it the seat cannot rotate out without the head and shoulder fouling.
Floor height above ground
Ground to the floor the seat sits on. The SLIFT Plus and SLIFT Plus+ are specified for up to 540 mm with a 400 mm lowering stroke; a higher floor leaves less drop at the kerb.
Passenger plus wheelchair
Weigh the two together, not separately. Rated load is per unit and covers the person, the wheelchair and anything carried on it — a powered chair with batteries is heavier than it looks.
Two more figures decide lifts rather than seats: the height the platform must reach inside the vehicle, and the space available below the floor if an under-floor unit is being considered.
Does the passenger stay in the wheelchair?
That single question splits the entire catalogue into three families. Answer it before you look at a single specification table.
Swivel and transfer seats
The passenger moves from wheelchair to vehicle seat with help, and the seat does the twisting and lowering. The smallest intervention: no floor cut, no platform, original interior mostly intact.
- Rated load 150 kg across the SLIFT range
- Rotation 0-90° manual or electric; 0-113° on the SLIFT Pro V2
- Needs clear height, clear width and a floor no higher than the published limit
- Not suitable if the passenger cannot leave the wheelchair
Wheelchair lifts
The passenger boards in their own wheelchair and is raised to floor level. Required whenever transferring is not an option, and the only family that works for a powered chair too heavy to move by hand.
- Rated load 250 kg to 350 kg depending on the family
- Side door, rear door, luggage bay or under the floor
- Needs a restraint system in most markets
- Needs more vehicle preparation than a seat
Ramps
For a small step or a low floor where a lift is unnecessary. Cheap, fast to deploy, and entirely dependent on the height difference and the available run at the door.
- Rated load 300 kg across the three ramp models
- Single, 2-fold and 3-fold — fold count sets the stowed length
- No power, no maintenance beyond the hinge and the surface
- Not workable where the floor is high and the pavement is short
Where on the vehicle it mounts
Two units with the same rated load can be completely different products depending on where they sit. The mounting position decides the vehicle preparation, the space lost inside and who can install it.
| Position | What it suits | Space inside | Vehicle work |
|---|---|---|---|
| Side door | MPVs, minibuses, side-loading taxis. The usual choice where the kerb is on the passenger side. | Platform folds into the doorway; some width lost at the aperture | Door and step area, floor reinforcement |
| Rear door | Vans and school buses where the rear opening is wider than the side and the vehicle parks nose-in. | Keeps the side of the cabin clear | Rear threshold, floor reinforcement, bumper clearance |
| Luggage bay | Coaches and intercity buses with a high floor and a rotary-arm lift. | None inside the passenger cabin | Bay structure and a floor-level opening |
| Under the floor | Vans and MPVs where cabin space cannot be given up at all. | Full cabin retained | Floor cut and a stowage cavity below; the highest preparation cost |
Every family on one page
Rated load is the published figure for the unit. Stroke, dimensions and door requirements are on each product page — read those against your four measurements before shortlisting.
| Model | Type | Rated load | Mounting | Choose it when |
|---|---|---|---|---|
| Swivel and transfer seats | ||||
| SLIFT Pro V2 | Electric swivel and transfer seat | 150 kg | Second row, side door | You need the deepest drop and the widest rotation in the range, plus door interlock |
| SLIFT Plus+ | Electric, detachable | 150 kg | Second row, side door | The seat has to leave the vehicle and continue as a mobile seat |
| S-OUT Pro | Swivel passenger seat | 150 kg | Front passenger position | The passenger travels in the front seat of a car or MPV |
| SLIFT Plus | Manual swivel seat | 150 kg | Second row, side door | No power available at the seat, or a simpler mechanism is preferred |
| Wheelchair lifts | ||||
| WL-D series | Platform lift, side or rear door | 350 kg | Side door, rear door | A van or school bus with a wide opening and a mid-height floor |
| WL-T | Rotary-arm lift | 350 kg | Luggage bay | A coach or intercity bus with a high floor and no cabin space to give up |
| Hydraulic platform lift | Hydraulic platform | 350 kg | Side door | A minibus or bus where a hydraulic drive is preferred over an electric screw |
| Under-vehicle lift | Stows below the floor | 300 kg | Under the floor | The cabin cannot lose any space and a floor cavity is acceptable |
| Mini-UVL 350 | Under-floor, higher capacity | 350 kg | Under the floor | Same as above, but the passenger and chair are heavier |
| Mini-UVL | Compact platform lift | 250 kg | Side or rear, small vehicles | A taxi or compact MPV where every kilogram and every millimeter counts |
| Ramps and restraints | ||||
| Folding ramp | Single fold | 300 kg | Door threshold | The step is small and the ramp has to deploy in seconds |
| 2-fold ramp | Folds in two | 300 kg | Door threshold | Stowage length behind the seat is limited |
| 3-fold ramp | Folds in three | 300 kg | Door threshold | Stowage space is very short and the ramp still has to be carried on board |
| Restraint system | Tie-down plus occupant restraint | Per system rating | Wheelchair position | Any lift installation where the passenger travels seated in the wheelchair |
Six ways a fit fails
None of these are manufacturing faults. All of them are decisions taken before the unit was ordered, and all of them are avoidable with a tape measure.
Starting from the vehicle nameTwo vehicles with the same badge can differ in floor height and door aperture by model year and trim. Measure the vehicle in front of you, not the one in the brochure.
Quoting the door frame, not the clear openingThe usable width is between the rubber seals with the door fully open. A 40 mm difference is the difference between a fit and a return.
Forgetting the seat is still occupied while it movesClearance has to be checked for a seated passenger, including shoulders and feet on the footrest, not for an empty seat on a drawing.
Adding the weights separatelyPassenger plus wheelchair plus bag is the load. A powered chair alone can be 100 kg before anyone sits in it.
Assuming the original seat base staysOn most installations the factory seat and its rails come out and a mounting plate goes in. That is a modification, and it has inspection consequences.
Leaving the documents until after deliveryIf the market requires a certificate number, find out which number exists before the order, not when the container is at the port.
What to check before the vehicle leaves the workshop
A commissioning checklist is supplied with every unit. This is the short version, and it is the same list whether the installer is in our network or not.
- Full rotation or full platform travel with the rated load on board, not empty
- Every locking position engaged and released by hand, twice
- Emergency manual release operated and then reset
- Wiring routed clear of the seat travel, fused at the correct rating, no scotch-locks
- Door interlock or travel inhibit working where the model has one
- No contact between the moving unit and trim, seals, fuel or brake lines
- Mounting fasteners torqued to the stated value and marked
- Restraint anchorages checked where a wheelchair travels in the vehicle
- Manual, wiring diagram and compliance documents handed to the owner
- Post-conversion inspection booked where the market requires it
Frequently Asked Questions
The questions that come up in the first ten minutes of a fitment enquiry, answered from the published specification of each model.
How much door opening does a swivel seat need?
For the SLIFT Plus and SLIFT Plus+, the published minimum is 990 mm clear height and 680 mm clear width at the door, with a floor height no greater than 540 mm. Below those figures the seat cannot complete its rotation and lower outside the vehicle. For the other models, check the fitment sheet for that model against the actual vehicle before quoting.
Do I need a swivel seat or a wheelchair lift?
It depends on whether the passenger stays in the wheelchair. If they can transfer to a vehicle seat with help, a swivel seat removes the lift-and-twist and is the smaller intervention. If they travel in their own wheelchair, a lift is required, because a swivel seat has no wheelchair platform.
What floor height can a swivel seat work with?
The SLIFT Plus and SLIFT Plus+ are specified for a floor height of up to 540 mm, with a 400 mm lowering stroke and a seat height of 500 mm. Higher floors reduce the drop available at the kerb, so the transfer becomes less level. Vans and minibuses above that figure need a different model or a lift.
Can a wheelchair lift fit a normal MPV?
Sometimes, and the deciding measurement is the stowed height, not the vehicle class. An under-floor unit stows below the floor and keeps the cabin clear; a platform unit needs the door aperture and the floor structure to take it. Measure the aperture and the underfloor space first, then match the model. Do not start from the vehicle name.
How much weight do these products carry?
Swivel seats: 150 kg across the SLIFT range. Wheelchair lifts: 250 kg for the compact Mini-UVL, 300 kg for the under-vehicle lift, and 350 kg for the WL-D, WL-T, hydraulic platform and Mini-UVL 350. Ramps: 300 kg. The rated load is per unit, not per vehicle, and it includes the passenger, the wheelchair and anything carried on it.
What is the difference between the ramp models?
Fold count, which decides the folded length rather than the load. The single-fold ramp is the shortest to deploy, the 2-fold and 3-fold ramps fold down further for storage in a vehicle where space behind the seat is limited. All three are rated at 300 kg.
Where does the installation happen?
At a local workshop, not at our facility. Velomove supplies the unit, the model-specific manual, the wiring diagram with pinout and a commissioning checklist, and can join a video call during a first install. The physical fitting, the vehicle preparation and the post-conversion inspection belong to the installer in the destination market.
What documents come with a unit?
Installation and operation manual, wiring diagram, packing list, and the compliance documents that exist for that model and market. Which certificates exist is set out on the compliance page: two carry a quotable number, and everything else is supplied on request depending on the market.
Rules, documents and supply
The guide tells you what to buy. These three pages cover what happens around it.
Compliance documents
Which standards apply, which two documents carry a checkable number, and who signs what.
See the documentsInstallation partners
Who fits the unit, what support comes with it, and where our responsibility ends.
See the networkOEM and private label
Branded units, agreed specifications and where the manufacturing actually happens.
See the program